General Engine Building Discussion -> Balance weights on piston
on 28 11 2020
|
|
54 days ago
|
Off Topic Discussion -> Ross-Tech OBD II SCANNER
on 15 10 2020
|
|
3 months ago
|
How to Degree a Cam -> True TDC Question
on 8 10 2020
|
|
3 months ago
|
Engine Building Fundamentals -> Bore gauge brand
on 8 10 2020
|
|
3 months ago
|
General Tuning Discussion -> Turbo Oil feed heat
on 4 10 2020
|
|
4 months ago
|
Webinar Questions -> 237-inlet restrictions with turbo restrictors
on 3 10 2020
|
|
4 months ago
|
Professional Motorsport Wiring Harness Construction -> Pinning last “circle” of milspec connector
on 3 10 2020
|
|
4 months ago
|
Engine Building Fundamentals -> blowby
on 28 9 2020
|
|
4 months ago
|
General Engine Building Discussion -> Bleeding Lifters on 4G63. Getting conflicting info.
on 27 9 2020
|
|
4 months ago
|
Practical Engine Building -> ARP main stud spins during torque procedure.
on 16 9 2020
|
|
4 months ago
|
General Tuning Discussion -> EJ25s: Forged Internals & Low RPM/Load Knock
on 11 9 2020
|
|
4 months ago
|
Understanding AFR -> Calibration or Verification of AF meter with Bosch LSU 4.9 sensor
on 10 9 2020
|
|
4 months ago
|
Practical Engine Building -> Wirelock life
on 7 9 2020
|
|
5 months ago
|
Engine Building Fundamentals -> bore measurement
on 7 9 2020
|
|
5 months ago
|
General Tuning Discussion -> Stand alone ECU
on 1 9 2020
|
|
5 months ago
|
Practical Reflash Tuning -> ECU software for Porsche 911 996 Turbo (2002)
on 31 8 2020
|
|
5 months ago
|
Practical Engine Building -> Ideas to clean engine parts(getting rid of sludge)
on 29 8 2020
|
|
5 months ago
|
General Engine Building Discussion -> Is it efficient to build a 1.8l 4 cylinder engine in a twin turbo configuration?
on 29 8 2020
|
|
5 months ago
|
Practical Reflash Tuning -> Doing Runs With An Automatic
on 23 8 2020
|
|
5 months ago
|
Practical Engine Building -> Seeking advice on where to remove material when balancing pistons
on 23 8 2020
|
|
5 months ago
|
General Tuning Discussion -> Start timing
on 23 8 2020
|
|
5 months ago
|
General Tuning Discussion -> Bmw 640d spun bearing, questions as to how, and Next steps
on 20 8 2020
|
|
5 months ago
|
Webinar Questions -> 157 - Direct Injector Timing
on 13 8 2020
|
|
5 months ago
|
EFI Tuning Fundamentals -> Peak vs Average Cylinder Pressure -> Torque
on 13 8 2020
|
|
5 months ago
|
Practical Engine Building -> Rod balancing limit
on 13 8 2020
|
|
5 months ago
|
Understanding AFR -> TIT measurement vs 4 port EGT
on 6 8 2020
|
|
6 months ago
|
EFI Wiring Fundamentals -> BMW E36 Connectors
on 4 8 2020
|
|
6 months ago
|
Practical Engine Building -> Bearings cleaning and inspection
on 1 8 2020
|
|
6 months ago
|
Understanding AFR -> MIVEC AFR AND IGNITION TIMING
on 1 8 2020
|
|
6 months ago
|
Off Topic Discussion -> Slow fuel pressure issue.
on 29 7 2020
|
|
6 months ago
|
Practical Engine Building -> turning a crankshaft
on 28 7 2020
|
|
6 months ago
|
General Tuning Discussion -> Intake restrictors tuning
on 28 7 2020
|
|
6 months ago
|
Practical Dyno Tuning -> Kpro killer first start high compression
on 28 7 2020
|
|
6 months ago
|
Practical Harness Construction - Club Level -> oldschool vintage rally car connectors - please help identify them
on 28 7 2020
|
|
6 months ago
|
EFI Tuning Fundamentals -> Mobil 98 - Pump gas or Iso-Octane?
on 24 7 2020
|
|
6 months ago
|
General Tuning Discussion -> RB26 Abnormally high EGT on one cylinder. Individual EGT setup. Map and Log attached. Haltech 2500
on 20 7 2020
|
|
6 months ago
|
Practical Harness Construction - Club Level -> Help Identifying FD3s Thermoswitch Connector
on 20 7 2020
|
|
6 months ago
|
Practical Engine Building -> Max Main Bearing Clearance to Big
on 20 7 2020
|
|
6 months ago
|
General Tuning Discussion -> Motorcycle Ideal Knock Sensor Placement
on 20 7 2020
|
|
6 months ago
|
General Engine Building Discussion -> Nissan/Datsun J18 engine
on 16 7 2020
|
|
6 months ago
|
Engine Building Fundamentals -> Wire Lock / Circlip installation HELP! So damn frustrating !
on 12 7 2020
|
|
6 months ago
|
Engine Building Fundamentals -> Calculating the Redline of Your Built Motor
on 11 7 2020
|
|
6 months ago
|