General Tuning Discussion -> A few questions on Plex Knock monitor settings
on 9 4 2021
|
|
2 days ago
|
General Tuning Discussion -> Hunting idle, even on open loop
on 9 4 2021
|
|
2 days ago
|
Off Topic Discussion -> Any HPA people or friends of HPA in San Diego or nearby with a dyno?
on 3 4 2021
|
|
8 days ago
|
General Tuning Discussion -> Coolant temps and when should I be concerened.
on 2 4 2021
|
|
9 days ago
|
General Tuning Discussion -> Knock, what's realistic?
on 1 4 2021
|
|
10 days ago
|
Off Topic Discussion -> Will CAN partially work if not wired correctly?
on 31 3 2021
|
|
11 days ago
|
General Tuning Discussion -> Can I use injector1 instead of ignition1 with Plex for individual cylinder detection?
on 30 3 2021
|
|
12 days ago
|
General Tuning Discussion -> Should I bottom out this stud for knock sensor?
on 28 3 2021
|
|
14 days ago
|
Off Topic Discussion -> Imperfection in new OEM MLS head gasket
on 23 3 2021
|
|
19 days ago
|
General Tuning Discussion -> Poll: What do you consider a safe minimum piston-valve clearance.
on 19 3 2021
|
|
23 days ago
|
General Engine Building Discussion -> How far can I go with cam timing and these clearances?
on 19 3 2021
|
|
23 days ago
|
General Engine Building Discussion -> Any reason why I can’t check v2v clearance with the head upside down on the workbench?
on 3 3 2021
|
|
39 days ago
|
Off Topic Discussion -> Best way to prevent rust off walls while head is off for a while
on 3 3 2021
|
|
39 days ago
|
General Engine Building Discussion -> Should head studs be staying finger tight? Is there a trick to this?
on 2 3 2021
|
|
40 days ago
|
General Engine Building Discussion -> How much should valves leak? (I may have solved the mysteries)
on 1 3 2021
|
|
42 days ago
|
General Engine Building Discussion -> Having trouble understanding valve lash with check springs installed and vtec locked
on 27 2 2021
|
|
43 days ago
|
General Engine Building Discussion -> Who's torque specs to go by?
on 27 2 2021
|
|
43 days ago
|
General Engine Building Discussion -> Need a sanity check on cam card, doesn't all add up.
on 27 2 2021
|
|
43 days ago
|
How to Degree a Cam -> Measuring piston to valve clearance with solid lifters/rockers
on 27 2 2021
|
|
43 days ago
|
General Engine Building Discussion -> How to set to 0.000 lash
on 27 2 2021
|
|
43 days ago
|
General Engine Building Discussion -> Now I've got my v2p clearances and they are shocking. Can this be right / am I this lucky?
on 26 2 2021
|
|
44 days ago
|
Off Topic Discussion -> How much do you change torque from spec for anti-seize
on 25 2 2021
|
|
45 days ago
|
General Engine Building Discussion -> Leakdown mystery
on 25 2 2021
|
|
45 days ago
|
General Engine Building Discussion -> Yikes! Help changing valve spring while head installed on block
on 24 2 2021
|
|
46 days ago
|
General Engine Building Discussion -> would a spare head with the same valves and cams & rocker arms have the same (or very close) v2v clearance?
on 22 2 2021
|
|
48 days ago
|
Off Topic Discussion -> Any gotchas to this knock sensor mounting solution?
on 21 2 2021
|
|
49 days ago
|
General Engine Building Discussion -> Avoiding v2v contact while while checking v2p clearances
on 20 2 2021
|
|
50 days ago
|
Off Topic Discussion -> LMA float protection
on 17 2 2021
|
|
53 days ago
|
General Tuning Discussion -> Relationship between VE & load
on 17 2 2021
|
|
53 days ago
|
General Tuning Discussion -> Knock detection system recommendations
on 17 2 2021
|
|
53 days ago
|
General Tuning Discussion -> Octane vs safe AFRs & knock detection
on 15 2 2021
|
|
55 days ago
|
General Tuning Discussion -> Cold start tuning under load
on 11 2 2021
|
|
60 days ago
|
General Engine Building Discussion -> So I've found True TDC and marked my crank pulley, now what (possible stupid question alert)
on 11 2 2021
|
|
60 days ago
|
How to Degree a Cam -> valve to valve clearance not worth considering?
on 3 2 2021
|
|
2 months ago
|
How to Degree a Cam -> Reseal cam caps after unbolting and rebolting?
on 3 2 2021
|
|
2 months ago
|
How to Degree a Cam -> TDC came up different each time?
on 2 2 2021
|
|
2 months ago
|
How to Degree a Cam -> Impact gun on crank bolt?
on 2 2 2021
|
|
2 months ago
|
Off Topic Discussion -> ZDDP how much is too much?
on 29 1 2021
|
|
2 months ago
|
General Engine Building Discussion -> Tips on marking the crank pulley for true TDC
on 29 1 2021
|
|
2 months ago
|
General Tuning Discussion -> Are AFRs accurate when under no load?
on 28 1 2021
|
|
2 months ago
|
General Tuning Discussion -> Lambda at idle
on 23 1 2021
|
|
3 months ago
|
Off Topic Discussion -> What are lower limits of rpm/load you can reach on the dyno?
on 20 1 2021
|
|
3 months ago
|
Off Topic Discussion -> Mystery Problem! Can't get idle low enough, Is it a mortal sin to mess with the throttle stop screw?
on 14 1 2021
|
|
3 months ago
|
General Tuning Discussion -> Why is there an idle setting for when vehicle is moving
on 18 1 2021
|
|
3 months ago
|
General Tuning Discussion -> Question about higher octane fuel
on 14 1 2021
|
|
3 months ago
|
General Tuning Discussion -> Realizing what a mess my tuner left for me. Need some guidance cleaning it up
on 13 1 2021
|
|
3 months ago
|
General Tuning Discussion -> Affect of changing spark plugs (gap & heat range) on existing tune
on 9 1 2021
|
|
3 months ago
|
General Tuning Discussion -> Target AFR map vs what is possible in Hondata s300 v3
on 8 1 2021
|
|
3 months ago
|
Understanding AFR -> Regarding a slightly richer target lamda with a cat
on 8 1 2021
|
|
3 months ago
|
General Tuning Discussion -> My first attempt at tuning had a mishap, need some reassurance / wisdom
on 7 1 2021
|
|
3 months ago
|