×

Sale ends todayGet 30% off any course (excluding packages)

Ends in --- --- ---

Unresolved Threads

Forum Posts

Courses

Blog

Tech Articles

= Resolved threads

Thread Latest Post
Einstar Vega on Mac?

by TheGrumpyPenguin on in Practical 3D Scanning

by TheGrumpyPenguin

Harness design with bulkhead/breakout panel

by Adam Stadnick on in Practical Motorsport Wiring - Professional Level

by Adam Stadnick

My USB to CAN is not connecting to the laptop

by Yaadie on in PDM Installation & Configuration

by Yaadie

My USB to CAN is not connecting to the laptop

by Yaadie on in PDM Installation & Configuration

by Yaadie

Load jumping around

by CetzRichard on in EFI Tuning Fundamentals

by CetzRichard

Suggestions on sheathing LSX engine harness

by dsrour on in EFI Wiring Fundamentals

by Six_Shooter

Confusion around factory crank/block stampings to determine correct bearing grades

by Mickwitchy on in General Engine Building Discussion

by Mickwitchy

Theoretical Discussion: F1 2026 Variable Compression & Transient Torque Spikes (MBT vs KLSA)

by harmont2007 on in EFI Tuning Fundamentals

by Andre.Simon

Recommendations for Wideband and Knock sensor.

by Jhtolsen on in Practical Reflash Tuning

by M:EP

#1 cylinder?

by Eric S on in How to Degree a Cam

by Eric S

1JZ trigger ecu master

by al500 on in EFI Tuning Fundamentals

by al500

Missing "397 | How To Use Extrudes, Cuts & Holes in CAD" on Webinar list

by McFly on in Webinar Questions

by McFly

Air intake temperature sensor settings

by cmvanditmars on in General Tuning Discussion

by David Ferguson

High vs Low side switching.

by Amaisel on in EFI Wiring Fundamentals

by M:EP

MoTeC M150 5v Rail Wiring

by jundii on in EFI Wiring Fundamentals

by jundii

AutoCAD - what are the best online training resources?

by F1Jim64 on in 3D Modeling & CAD for Motorsport

by F1Jim64

B6304T4 swapped Volvo XC90

by GregAbles on in Build Threads

by greenamex2

Need Guidance on tools for starting tune.

by akhanish7 on in EFI Tuning Fundamentals

by akhanish7

Increasing Ignition Energy & Retarding Timing

by Mobs on in General Engine Building Discussion

by Mobs

Transmission Tuning

by Gritworx on in Diesel Tuning Fundamentals

by Gritworx

Rich in stead state, lean passing through quickly? Tunerstudio MS2

by bjacks on in General Tuning Discussion

by bjacks

2.0 Ecotec LSJ Unstable idle.

by Mcginitie01 on in EFI Tuning Fundamentals

by Mcginitie01

ST170 VVT Cam Trigger Issues

by gorumcen on in EFI Tuning Fundamentals

by Wedge905

Hello from the sunny UK.

by Beepee123 on in Member Introductions

by Beepee123

Sensor Ground and PnP

by Ambre on in Practical Motorsport Wiring - Club Level

by Ambre

EMU Pro

by kemp36 on in Practical Standalone Tuning

by GregAbles

CAN Bus Auto Theft in Chicago.

by robbhulburt on in Off Topic Discussion

by robbhulburt

Evo 10 midband partial throttle lift brick wall

by jschneider82 on in General Tuning Discussion

by jschneider82

M57 wiring harness

by Kopilas99 on in EFI Wiring Fundamentals

by Kopilas99

Carbon skinning

by greenamex2 on in Motorsport Composite Fundamentals

by greenamex2

Sensor failure stratedgy

by JordonMusser on in MoTeC M1 Software Tutorial

by JordonMusser

[GDI] Base map buildout: HPFP and Injector parameters

by Fadeluc_123 on in EFI Tuning Fundamentals

by David Ferguson

Can bus immobilizer

by snowerf1 on in CANBus Communications Decoded

by snowerf1

No Low Pressure Fuel Sensor Fitted - OEM

by Fadeluc_123 on in EFI Tuning Fundamentals

by OMS

Hello from Lancaster California

by T3 A2 RIDER on in Member Introductions

by T3 A2 RIDER

Would anyone have a list of the tables/maps that the Bosch MED17.7.x uses to cross check each other.

by Twmg on in Practical Reflash Tuning

by Twmg

Injector Scaling

by Mohamad adeb alqroo on in Practical Reflash Tuning

by Mohamad adeb alqroo

Exhaust Lambda and mass flow Lambda disagree

by Oskar on in General Tuning Discussion

by Oskar

3D Scan to Solid

by Deek on in 3D Modeling & CAD for Motorsport

by Connor Anderson

How do you use HP Tuners Scanner to convert stock 2017 GM 6.2L LT-1 wideband O2 sensor voltage value into lambda values

by CalGator on in Practical Reflash Tuning

by CalGator

Printer Recommendations

by jungalwala on in Practical 3D Printing

by Connor Anderson

We usually reply within 12hrs (often sooner)

Need Help?

Need help choosing a course?

Experiencing website difficulties?

Or need to contact us for any other reason?